DW3067PARTS

DIGGING TEETH

CUP TEETH

STD. DUTY

(3/4" bolts, 3.0625" on center)

135911 CUP TOOTH R/H $14.23

135910 CUP TOOTH L/H $14.23

CARBIDE CUTTERS

BULLET BIT TYPE

,BITS ARE NOT INCUDED

135975 BULLET BIT HOLDER $51.52

6" CUT R/H

135976 BULLET BIT HOLDER $51.52

6" CUT L/H

135974 BULLET BIT HOLDER $51.52

8" CUT R/H

135973 BULLET BIT HOLDER $51.52

8" CUT L/H

765CBFP Cap Carbide Bit with Flare

Puller Groove & Wedding Band $10.95

Bullets not included with side mounts

765CRFN Cap Carbide Bit with Flare & $11.95 External C-Clip Retainer

CARBIDE CUTTERS

SHARK TOOTH

136276 SHARK SIDEMOUNT CENTER

6" CUT R/H $51.72

136275 SHARK SIDEMOUNT CENTER

6" CUT L/H $51.72

136274 SHARK SIDEMOUNT CENTER

8" CUT R/H $51.72

136273 SHARK SIDEMOUNT CENTER

8" CUT L/H $51.72

CHRL3067 REPAIR LINK (INC 2 PINS) 306CL $62.30 CONNECTOR LINK $52.30

306RL ROLLER LINK $19.80 306CP CHAIN PIN (WITH KEY) $7.25

If you have questions

call 1-800-4471941 or Email

[email protected]

Fax 877-255-7781

3.067" PITCH: BARE DIGGING CHAIN & DIGGING CHAIN ASSEMBLIES

The welded Shark Tooth Chain is a maintenance free low profile chain assembly. The carbide tipped shark tooth will outlast the chain. Tension Adjustment is the only maintenance required. A great chain for digging HARD ROCK, CALICHE, CORAL, AND LIMESTONE.

Low-cost trencher chain. Best for trenching SAND, SANDY LOAM, LOOSE SHALE, LOOSE SOIL, CALICHE AND CLAY.

This 50/50 chain configuration allows for trenching in almost any type of ground. The carbide tipped replaceable bullet bits are bolted to the chain and used to break up the ground. The cup teeth follow to clean the trench. Use on LOOSE DIRT, MEDIUM AND HARD ROCKY SOIL.

This 50/50 chain configuration allows for trenching in almost any type of ground. The non-replaceable Shark Tooth will outlast the chain. The cup teeth follow the Shark Tooth to clean the trench. Use on LOOSE DIRT, MEDIUM AND HARD ROCKY SOIL.

The bolt-on rock and frost chain are used on HARD ROCKY CONDITIONS AND FROZEN GROUND. This chain uses replaceable carbide tipped bullet bits to pick and fracture hard rock and frozen ground.

CALL

800-447-1941

TO OBTAIN CURRENT PRICING ON DIGGING CHAIN

CALL

800-447-1941

TO OBTAIN CURRENT PRICING ON DIGGING CHAIN

140717 SPLIT 10 TOOTH $262.30

141589 SPLIT 11 TOOTH (RT70, RT90 & RT115 W/H911 ATT.) $295.60

AUGER DRIVE SPROCKET

140665 AUGER DRIVE SPK. 10 TOOTH HEX SHAFT,

5.625" HUB LENGTH $282.30

145244 HEX SHAFT $147.88

(1.75"X 23.375)

125620 1.75" HEX FLANGE AUGER BEARING $173.60

ROLLER ASSEMBLIES SPROCKET ASSEMBLY

CHAIN DRIVE SPROCKETS

142756A ROLLER ASSY. 17" $ 998.23

142757A ROLLER ASSY. 19" $1084.50

(145589 URETHANE DIRT WASHERS NOT INCLUDED

WITH ASSEMBLIES)

145589 URETHANE DIRT WASHER $36.75 each

166437 IDLER SHAFT $68.95

(1.50"X 5.25" FOR 17" & 19" ROLLERS)

105377 JAM NUT FOR ABOVE IDLER SHAFTS $6.33

190183 SEAL & BEARING SET(142756 & 142757) $338.15

140656 IDLER SPK ASSM. 10 TOOTH $508.40

180440 IDLER SHAFT (1.5"x5.25" BOOM END) $32.02

180441 IDLER SHAFT (1.5"x4.30" IDLER) $38.20

105377 JAM NUT FOR ABOVE IDLER SHAFTS $6.33

125309 SEAL & BEARING KIT (FOR 140656) $323.14

180026 FIBER WASHER (2 REQ. not included in 125309) $7.70

CHAIN PARTS

R40, R60, R65, 5010, 5110, 6510, 7510, 7610, 8020, RT55, RT70, RT80, RT90, RT95, RT115, RT115 QUAD, HT115, AH400, AH500, A615, A610, H700, H911

CUP TEETH

HEAVY. DUTY

(3/4" bolts,2.66"to3.50" SLOTTED)

183147A1 CUP TOOTH R/H $20.35

183148A1 CUP TOOTH L/H $20.35

QUICK FIND

Do you need a chain for trenching in extreme conditions? Use this chain in HARD ROCKY CONDITIONS, FROZEN GROUND, ASPHALT AND CONCRETE. The welded H-plate chain gives you the best bit penetration angle plus great trench clean out. This assembly has heavy-duty, heat-treated pockets and rock bits with pocket protectors.

DITCH WITCHR

Using 3.067" Pitch Chain