PARTS FOR DITCH WITCHR
USING 2.00" PITCH CHAIN
CARBIDE CUTTERS
BULLET BIT TYPE
136036 4” RIGHT Cut Side Mount
Bullet Bit Holder $26.75
136037 4” LEFT Cut Side Mount
Bullet Bit Holder $26.75
136038 5” LEFT Cut Side Mount
Bullet Bit Holder $26.75
136039 5” RIGHT Cut Side Mount
Bullet Bit Holder $26.75
136040 6” RIGHT Cut Side Mount
Bullet Bit Holder $26.75
136041 6” LEFT Cut Side Mount
Bullet Bit Holder $26.75
765CBFP Cap Carbide Bit with Flare
Puller Groove & Wedding Band
765CRFN Cap Carbide Bit with Flare &
External C-Clip Retainer
CARBIDE CUTTERS
SHARK TOOTH TYPE $28.00
136236 SHARK SIDEMOUNT CUTTER 4" CUT R/H
136237 SHARK SIDEMOUNT CENTER 4" CUT L/H
136238 SHARK SIDEMOUNT CENTER 5" CUT L/H
136239 SHARK SIDEMOUNT CENTER 5" CUT R/H
136240 SHARK SIDEMOUNT CENTER 6" CUT R/H
136241 SHARK SIDEMOUNT CENTER 6" CUT L/H
REPAIR LINK (INC 2 PINS) CHAIN REPAIR PARTS
CHRL200 $27.10 137202H CONNECTOR LINK $17.96
135203 ROLLER LINK $12.15 135351 CHAIN PIN (WITH KEY) $4.95
4 PITCH SPACING BARE CHAIN
4 PITCH CUP TOOTH CHAIN 6" CUT
2 PITCH SPACING BARE CHAIN
2 PITCH CUP TOOTH CHAIN 6" CUT
2 PITCH 50\50 COMBO CHAIN 6" CUT
(CARBIDE TIPPED BULLET BITS & CUP TOOTH)
2 PITCH 50\50 COMBO CHAIN 6" CUT
(CARBIDE TIPPED SHARK TEETH & CUP TOOTH)
SHARK TOOTH WELDED CHAIN 6" CUT
2 PITCH ALL ROCK & FROST CHAIN 6" CUT
(CARBIDE TIPPED BULLET BITS)
If you have questions
call 1-800-4471941 or Email us orderdesk@replacementdiggingparts.com
Fax 877-255-7781
2.00" PITCH BARE DIGGING CHAIN & DIGGING CHAIN ASSEMBLIES
(PITCH IS THE CENTER TO CENTER MEASUREMENT OF THE CHAIN PINS)
(NUMBER OF LINKS ON A CHAIN IS THE NUMBER OF CHAIN PINS DIVIDED BY 2)
The welded Shark Tooth Chain is a maintenance free low profile chain assembly. The carbide tipped shark tooth will out last the chain. Tension Adjustment is the only maintenance required. A great chain for digging hard rock, caliche, coral, and limestone
Lowest Cost trencher chain. Use in the easiest digging conditions such as sand, sandy loam, loose shale, loose soil and sticky clay or dirt..
Low cost trencher chain. Best for trenching sand, sandy loam, loose shale, loose soil, caliche and clay.
This 50/50 chain configuration allows for trenching in almost any type of ground. The carbide tipped replaceable bullet bits are bolted to the chain and used to break up the ground. The cup teeth follow to clean the trench. Use on loose dirt, medium and hard rocky soil.
This 50/50 chain configuration allows for trenching in almost any type of ground also. The non-replaceable Shark Tooth will out last the chain. The cup teeth follow the Shark Tooth to clean the trench. Use on loose dirt, medium and hard rocky soil.
The bolt-on rock and frost chain is used on hard rocky conditions and frozen ground.This chain uses replaceable carbide tipped bullet bits to pick and fracture hard rock and frozen ground.
CALL
800-447-1941
TO OBTAIN CURRENT PRICING ON DIGGING CHAIN
CALL
800-447-1941
TO OBTAIN CURRENT PRICING ON DIGGING CHAIN
DIGGING CHAIN DRIVE SPROCKETS
142005 SPLIT 10 TOOTH $75.00
(V30,2300,2310)
140732 SPLIT 14 TOOTH $126.40
(R30,R40,3210)
DRIVE SPROCKETS FOR 3500, 3700, RT40, RT45
142127 SPLIT 12 TOOTH 12mm HOLES $123.10
142029 SPLIT 12 TOOTH 1/2" HOLES $123.10
142030 SPLIT 14 TOOTH 1/2" HOLES $155.00
142025 SPLIT 12 TOOTH 5/8" HOLES $125.00
142026 SPLIT 14 TOOTH 5/8" HOLES $175.00
SPROCKET & ROLLER
140654 IDLER SPK ASSM. 9 TOOTH 180062 DIRT SHIELD $2.25 (includes bearing set) $110.00
180448 IDLER SHAFT $12.50
(BOOM END 1.25"3.75")
180534 IDLER SHAFT $15.75
(BOOM END 1.25"X4.75")
142751 ROLLER WITH BEARING (14.5 dia.) 105313 JAM NUT (1.25") $3.75
(includes bearing set) $296.00
125209 BEARING SET (for 140654 & 142751) $44.00
142031 AUGER DRIVE SPK. 14 T $225.00 AUGER DRIVE SPROCKET 145244 HEX AUGER SHAFT $110.00
W/ HEX DRIVE 125620 1.75" HEX FLANGE AUGER BEARING
$115.00
Freight Special $25.00 on On line Orders (LImited to the continental U.S.)
CUP CUTTERS
(1/2" bolts, 2" on center)
135925 CUP TOOTH R/H $5.40
135924 CUP TOOTH L/H $5.40
DIGGING TEETH
CHAIN DRIVE SPROCKETS
